arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 1m 29d Gender: Male Location: Perth Posted 18/04/11 12:02 AM Share Posted 18/04/11 12:02 AM Should be able to stretch to a 3+How much would it cost for install roughly, any idea?Call Simon and get a quote Link to comment Share on other sites More sharing options...
Superpursuit83 Member 201 Member For: 17y 6m 11d Posted 18/04/11 06:09 AM Share Posted 18/04/11 06:09 AM Did they check your tint with some sort of light meter or did they just guess it maybe to dark , the way they guess the cars to low, or the exhaust is to loud. Or your tyres are to wide. Cops, mate what can I say. Iam sick of them making stuff up.It does not matter to a copper. They only have to SUSPECT a problem to make you get your car checked at an inspection pit. Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 1m 1d Gender: Male Location: Perth Posted 18/04/11 07:35 AM Share Posted 18/04/11 07:35 AM go the 3+ ... ive done 55,000 hard KMs in my xr8 since getting that clutch, and it has never failed me.as for rims, I wouldnt purchase wheels in WA, except for JPC ... but if I could, id buy from eastern states or overseas, as Perth wheel/tyre companies are ripoffs! Link to comment Share on other sites More sharing options...
XF Falcon <put funny sh*t here> Member 3,365 Member For: 18y 1m 17d Gender: Male Location: Perth, NOR Posted 18/04/11 10:10 AM Share Posted 18/04/11 10:10 AM (edited) Anyone installed a tail shaft loop on their BA/BF/FG sedan before? If so where do you have to place it? Need a definite answer by next Monday Edited 18/04/11 10:11 AM by XF Falcon Link to comment Share on other sites More sharing options...
Cheaty McCheats Totally not a Cop Donating Members 821 Member For: 13y 11m 1d Gender: Male Location: Melbourne Posted 18/04/11 10:18 AM Share Posted 18/04/11 10:18 AM (edited) Spoke with West Racing Motor Development today, quoted $2300 for 3+ and fitment. Do you think $500 is reasonable for the install?Also spotted a white R-spec today on south st / stock rd intersection. Had SA plates.Also, this is the car that is always parked across the road from my work (mentioned in previous post): Edited 18/04/11 10:20 AM by CyanideIllusions Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 3m 3d Gender: Male Location: Perth Posted 18/04/11 10:39 AM Share Posted 18/04/11 10:39 AM $500 is average. Should be able too knock it out in 2 to 3 hrs on a hoist.I can do it in 3.5/4hrs on the floor with a jack so anybody with a hoist and trans jack, and air tools @ hand should be a fair bit quicker!I´d ring Simon @ XFT he replaced more clutched than he can probably recall Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 1m 1d Gender: Male Location: Probably above atmospheric pressure Posted 18/04/11 11:45 AM Share Posted 18/04/11 11:45 AM Altezza's on an R-Spec...oh well, "to each their own". Link to comment Share on other sites More sharing options...
RIP_HSV HOON Member 1,636 Member For: 14y 9m 11d Gender: Male Location: W.A Posted 18/04/11 12:37 PM Share Posted 18/04/11 12:37 PM Anyone installed a tail shaft loop on their BA/BF/FG sedan before? If so where do you have to place it? Need a definite answer by next Monday Told ya already Link to comment Share on other sites More sharing options...
Adrian6T T.P.I.S. Donating Members 2,578 Member For: 20y 23d Gender: Male Location: SoR, WA Posted 18/04/11 12:45 PM Share Posted 18/04/11 12:45 PM go the 3+ ... ive done 55,000 hard KMs in my xr8 since getting that clutch, and it has never failed me.When you run bugger all ponys they will last forever. Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 1m 29d Gender: Male Location: Perth Posted 18/04/11 01:21 PM Share Posted 18/04/11 01:21 PM (edited) Spoke with West Racing Motor Development today, quoted $2300 for 3+ and fitment. Do you think $500 is reasonable for the install?Its in the ball park. Call Simon and see if he will do it cheaperDont forget to put in a malwood remote clutch bleeder while the box is out. Edited 18/04/11 01:23 PM by arronm Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now