Jump to content

Quarter Mile Times & Details


Cro

Recommended Posts

  • Member
  • Member For: 20y 8m 3d
  • Gender: Male
  • Location: Mackay NorthQueensland
can I please add in the Victoria section my NOS XR8 ute

10.70 @ 127 mph 1.52 60ft.

Thanks

Chris

High Criss, Well done mate! :blush:

did she crack a wheel in the air?

David

Link to comment
Share on other sites

  • Replies 183
  • Created
  • Last Reply

Top Posters In This Topic

  • Member
  • Member For: 18y 9m 6d
  • Gender: Male
  • Location: melbourne

Hey guys ,went to calder on friday night, had a few runs and to my utter surprise I managed to run a 12.67 sec!! its a 03 model Ba 4spd Auto!!! was really only expecting to run maybe if I was lucky a low 13 but cant beleive it!!

all I can say is how good is Horse Power Factory!!! Must admit though I was a bit disapointed when I first got my car back and it only made a low 225rwkw but I finally got off my arse and went out and ran it and now I understand and should of listened to Rob that bigger numbers dont always mean better times!!!,I mean they found an extra 50kw from it! my 60ft times were again piss poor as they are still not up to standard!!!! still thing was going so well that night and just kept pulling right to the line. Just wanted to ask for feedback from u guys if this is a respectable time for the power and mods I have? Also is there (reading from my time slip) any more time I can squeeze out of it!!! As for mods I only have a edit and tune, F6 cai and a high flow metal cat. Also was running on factory dunlop rubber with pressures at 24 psi. Also not sure on which way to go with next mods?? should I strengthen the auto and put a 2500 to 2700 stall convertor in with transmission cooler?? or should I go injectors and valve springs???

cheers Ryan

post-8592-1177202410_thumb.jpg

post-8592-1177202518_thumb.jpg

Edited by sleeper69
Link to comment
Share on other sites

  • Donating Members
  • Member For: 20y 5m 1d
  • Gender: Male
  • Location: N/W Sydney

that's a very good time for the power you have..Id imagine that it would read higher on other dyno's.First of all id be getting a tranny cooler atleast.

If you want to go quicker with the setup you have then put a set of MT's on..I knocked 2tenths off my 60foot and et with them.. :spoton::blink:

Link to comment
Share on other sites

  • Member
  • Member For: 18y 9m 6d
  • Gender: Male
  • Location: melbourne
that's a very good time for the power you have..Id imagine that it would read higher on other dyno's.First of all id be getting a tranny cooler atleast.

If you want to go quicker with the setup you have then put a set of MT's on..I knocked 2tenths off my 60foot and et with them.. :spoton::blink:

Thanks mate yeah rapted at the time, guess there dyno reads abit lower to other dynos!! yeah I think the tranny cooler is certainly going to be the first thing to get done, dont want any dramas with rebuilding auto etc!!!! got a set of yokohama semi slicks at home, but was a last minute thing to go out on friday so didnt have time to get them fitted...

cheers Ryan

Link to comment
Share on other sites

  • Here since the start...
  • Lifetime Members
  • Member For: 21y 9m 4d
  • Gender: Male
  • Location: Victoria
Hey guys ,went to calder on friday night, had a few runs and to my utter surprise I managed to run a 12.67 sec!! its a 03 model Ba 4spd Auto!!! was really only expecting to run maybe if I was lucky a low 13 but cant beleive it!!

What other times did you run?

List has been updated. :roflmbo:

Link to comment
Share on other sites

  • Member
  • Member For: 18y 9m 6d
  • Gender: Male
  • Location: melbourne
What other times did you run?

List has been updated. :roflmbo:

Hey Adam thanks for including me into the list. sorry I forgot to include the full details they are 12.670 at 111.23 mph with a 60 ft time of 2.114 My other few runs were a 12.8, 13.02, 13.08, these were done with sh*t 2.2 60 ft times and with traction being a problem..

cheers Ryan

Edited by sleeper69
Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.



×
  • Create New...
'