Search the Community

Stumbled across a brand of coilovers that I'm unfamiliar with anyone heard of them or running them at the moment. Neomax S Coilovers for the FG Falcon found the carmodsaustralia website at $1,399. Any opinions or thoughts would be interesting for a street application with obvious spirited driving and a low stance setup but nothing that's not practical. Currently running 19inch MK2 Luxpac limited addition wheels. Additionally any thoughts on MCA Street Greens vs XYZ vs BC Racing coilovers all for spritied street driving on a low stance.

I have a ba series 1 xr6t that's lowered. It says im right on the capacity to tow my van at 2300kg. But it doeant feel like its pulling that well and struggles. Is this because my car is lowered and has 19 inch rims? What are the implications. I get nervous towing it.

Specifically for my FG Turbo turbo ute if someone would be kind enough to measure for me! But if people have specs for other models this post can serve as a repository. Wheel center to guard measurements plus maybe bump-stop to axle measurements for us tray back utes. Been playing with my new Shockworks coilovers (loving them btw!) but my new worksite involves 6 speed humps that I'm scraping bumper & about 1m of sides on, so I've gotta jack the ute back up & I'm wondering what standard ride height actually is since I've always been overweight.

Most people take their lowered XR6 in for a wheel alignment and are informed that there's not enough room left on the camber bolts for the amount of shims required to adjust the camber back to factory specs. I was in the same boat, I've lowered the front of my FG ute using SSSL springs and then it's another 8mm lower again because I have Bilstein shocks with the spring installed on the lowest of the 3 settings. HTG measurement is around 335mm (which fills the guard perfectly). My camber was around -2.5° so I needed 1.5° of adjustment to bring it back to -1.0° Now I only had around 10mm left on the upper control arm bracket bolts. The figure for adjustment (from Superpro) is ~9mm of shims = 1° of adjustment. This means I would need around 13.5mm of shims installed to correct the camber. The bolts were not long enough obviously, any suspension shop would say "you need a camber kit". Superpro make a camber kit which is "designed to allow Camber Adjustment on Standard Height & XR Ride Height Vehicles only." The kit is around $100 and you need two kits per vehicle so that's 200 bucks. Each kit comes with 2 brackets, 3x 6mm, 2x 3mm and 4x 1.6mm shims BUT you need to put 1x each shim on EACH bracket for the kit to be the same as standard. So really you're only getting 1x 6mm, 0x 3mm and 2x 1.6mm for adjustment. How am I supposed to install 2x 13.5mm of shims per side with only 1x 6mm shim and 2x 1.6mm shims? The kit might be preferable for a suspension shop which has extra shims they can use but you've just basically forked out $200 for some brackets with longer bolts and no change to the camber (and I'm not sure just how much longer the bolts are after putting 1 of each shim back on?). I ended up going the DIY option which is installing longer bolts into the standard brackets. It's easy, costs $3-$5 for 8x M10x45mm bolts and only took an hour or so. First you need to remove the brackets from the car. I have a hoist but its easy to do on jack stands just remove the wheel, undo 2 bolts on the upper control arm then undo the 4 bolts in the engine bay and the 2 brackets will come out. Check the condition of your upper control arm bushes, mine were stuffed. Make sure you take note of previously installed shims and their positions. 1 bracket removed This is the bracket, that's a shim. Now, find a bit of heavy wall pipe that fits over the head of the bolt and put the pipe in a vice. Position the bolt head on the pipe and hit the bolt through with a hammer. The bolts are fusion welded onto the bracket but come out pretty easily. You'll need to clean up the welds so the new bolts sit flush. That's a 5mm shim on the right. Length of old bolt is 35mm Length of new bolt is 45mm (M10 bolts btw) Now you can either just place bolt through or you can weld them in to make them easier to do up in the vehicle. I welded my bolts in and a quick coat of paint. After that it's just reassembly making sure to put the shims in their original positions. I milled up some 12.5mm shims out of alluminium which you can see behind the factory shim in this pic. I still need to get a wheel alignment but this should help cut down the amount of adjustment required. Shims are pretty easy to make, if they don't need to be removed easily just use some flat bar in whatever thickness you want and drill 2 holes.. easy. Your wheel alignment place will have shims anyway. The Superpro shims are made to easily slot in without removing the bracket. That's all there is to it.. hope it helps save forking out $200

looking to lower my bf mk2 rspec, most likely with king springs...just wanting to see pictures so I can roughly see what it will look like. cheers

hey guys just found out that ineed new front shocks so I thought I might look at my fg xr6t instead and sort of don't really know where to start. I've forund this package on fleabay http://www.ebay.com.au/itm/Falcon-FG-KING-SPRING-MONROE-SHOCK-Lowered-Suspension-Package-/300776120075?pt=AU_Car_Parts_Accessories&hash=item4607a75f0b but not sure if I need to buy anything else to go with it or if its any good, any decent feedback would be greatly appreciated. Thanks.