fluke

Hi, just wanted to know if there is a difference between the rear ABS sensors on a BA/BF Falcon Sedan to a ute/wagon and if so what the difference is Ie: angle, position or shape, if anyone had a pic of a ute/wagon one that would be great.

Just a quick question, I am looking at a service and touch up on my trans and was thinking of putting a higher stall in 2500rpm to 3000rpm. Will I need to get the car tuned or adapted to suit or will it run ok Its a BA 6 N/A with the 4 speed auto and 3.23 diff gears. Thanks

Hi, just noticed tonight that the Airbag /safety belt pretensioner light is coming on while driving. It doesnt seem to be on constant, more when hit the bumps and stuff but even just little bumps make it illuminate. Any help on information is appreciated, and I cant quite remember but is the control module behind the ICC for the Airbag/Safety belt pretensioners.

With these mods makes it quite good to take off compared to standard and very driveable normally. yeah its a N/A. Cheers

Hi just after advice, Got a Falcon sedan BA and gunna be selling soon but gotta decide whether to take out or leave a couple mods on the car. I can A: Sell the car with the 4:11's(4:10's actually but we all say 4:11's) , high stall and Flash tuner or B: Take these bits out which will cost some $$$ to reinstall the standard stall and replace the original diff and then sell the car. Whats peoples thoughts, with these mods the car is still very drivable at a normal pace but also gives a nice pick up over standard when needed though. Cheers

Always like to get a second opinion on things looking at 16 x 6.5 , +40 Offset These figures should fit ok on the falcon yes, as it means they are only sitting in an extra 5mm each side.

So, 16x8 +22 front and 16x9 +22 rear on BA Sedan wouldnt work. Tried talking to a wheel shop but they just confused me, more sensible responses on here

Havent seen anything on change over, it may be cheaper and quiker just to replace the driveshaft. Hope you can get it sorted quickly though

That would be nice, definatley improve the power figures, but atmo minister of finance has higher power figures that prevent any upgrades, ha ha

Would love to go shopping and come home with one of those, nice

Nice, love that colour

I need a service on my BA N/A 6 auto, what is reccommended and is there anything they can do while servicing, filter fluid change, mods that will tighten up and give a bit more life to the auto. Doesnt require rebuild just yet. Thanks

Nice write up,

Hi, what is the offset range we can work with for wheels on a BA/BF Falcon, between +35 and +40 or what is best recommended. I have +35 on now which I think is also the the standard offset.

approx 160-175 depending on tune

Any other results people like to share

Update, installed the trans cooler and temp gauge and a pressure gauge, ended up adapting some high pressure air compressor adapters to run the temp sender and pressure sender. works well just need a higher pressure gauge as the trans pressure is very high. All up the adapter block was about $30 and works well. Thanks for advice given

Just an update due to hi pressure required in the line normal pressure gauges dont work as they dont read high enough, will have to look at a marine type trans press gauge which read up to 450psi

I thought it would be too high, but I would much rather check. thanks for the reply

Hi, this may be a bit of a long shot but got an option of some 16x8 and 16x9 supra rims for some spares but the quoted offset is +50 Being wider rims than the standard 6.5 inch to 7.5 inch rims. Will these fit on a BA Sedan. Thanks for any help

So the tally so far is : BA/BF N/A 6 Standard - mid to low 7's G tech measure N/A 6 - N/A BA Auto is approx 8.2- 8.3. 2006 BF XR6 Turbo 6sp MANUAL - 6.3 seconds Seem respectable for such a heavy car, can they go lower

Sorry, that would be BA BF. models

Just wondering what the standard 0-100 time is for a non turbo and for a turbo. And what are people pulling once they have done some mods.

The offset means that between the +27 and +36 there is a difference of 9mm that they will sit further out, is that the correct way of looking at it. Thanks for the help

Got an opportunity to get some rims just for drags They are 16 x 8.5, +27 offset, Is that enough offset or would it be cutting close as I know BA sedan run a +36 up to +40 but unsure about less offset