Coley

Found out today from ford that the bf mkii xr6 and xr6 turbo have the same bonnet as the ba. Only the normal Bf model has the diff bonnet

Just wondering how to fit the bonnet protector on a bf mkii. The instructions say there should be studs to screw the nuts onto but under my bonnet at the front there are just holes. Anyone fitted one to a bf or have any pics? Thanks

I've got 310rwkw and am still using the stock clutch and have been for a while. Just dont launch hard off the line and you will be fine

Have been trying to solve the same problem. Was thinking of just buying a small digital led pencil one to stick below the speedo

A truck drove into me yesterday as I was merging into traffic and scrapped the side of my car. He said he didn't see me but I dont think he was even watching the road as I was already half in the lane and it was in heavy traffic so we would have been doing under 20kmph. Unfortunetly because there was dashed lines in the merging lane I am at fault because I should have given way to him even though I was already halfway into the lane and he drove forward into me. Hopefully my insurance will cover my car but I just want to know if anyone has had to replace the rear tub in there ute before? And how much it cost them? I dont think you would be able to hit out the dint. Here are some pics:

Great prices I wish I waited for this group buy. They fit the xforce gauge pod without modifications not sure about the fpv one. Only problem that I had was the plastic xforce pod seemed to expand in the sun so I had to put a little bit of silicon on the gauge to hold it in. You can't notice it and it worked well. The only problem with the gauges is if they get really hot in the sun they seem to get a bit blurry but go back to normal once they have cooled down.

I just saw this last night on boost cruising. Thought I would paste the info on here.

"In light of the horror unfolding in victoria as I type I am proposing cruise to raise funds to help the poor buggas left behind to deal with the fallout. A cruise will take place on Sunday the 22nd of Feb. Staging point will be at Swifts Rugbly League Club carpark at Yamanto, Qld. Departure time will be 8.30AM sharp. There will be a food vendor at the cruise destination and I will be hitting him up for a dontation of some of his profit garnered by our presence. Cruise donation of 10 dollars per car will be the price and if any members have contacts a couple of worthwhile raffle prizes wouldnt go astray. Any further donations will be gratefull accepted. Funds will go to the red cross bushfire appeal Line up you plebs. lets help where we can. Inappropriate behaviour will NOT be tolerated, and we will have NO hesitations in reporting you straight to the police. " I'll post more details and keep this first post up to date when more info comes to hand on the cruise. The club also will be taking on donations for those that can not make it. I'll provide the bank details shortly for this. CRUISE DETAILS - Date: Sunday, 22nd of Feb, 2009. Meet at: Swifts Rugbly League Club at Yamanto from 8:00am. Depart: 8:30am Route: From Yamanto to Rosewood.. has a crappy road but not long Rosewood to Warril View via Mt Walker... Then from Warril View to Aratula... and then onto the Cunningham Highway. From Aratula and finishing up at Lake Moogerah. has some nice road out along that way. There will be a food vendor on site at the final destination . There will also be raffles to help further raise money from prizes given to the SAU Car Club from the club sponsors and also the ability to give further donations, etc. >>PRIZES TO BE RAFFLED OFF Bring swimwear for those want to cool off. ------------------------------------------------------------------------------------ SOUTHSIDE MEET I've decided to organise a southside meet to better help guide everyone out to Yamanto and to have a group turn up to the destination. Those keen.. details below and I've also just updated the 1st post with these details. Meet: Sunnybank Pinelands Shopping Centre Carpark (left hand side where nando's is) Time: 7:30am meet and leave right on 7:45am and no later!! ------------------------------------------------------------------------------------ PLEASE NOTE THAT THIS IS A OPEN CRUISE FOR ALL TO ATTEND. THIS IS JUST BEING ORGANISED BY THE SKYLINES AUSTRALIA QLD CLUB More details & discussion can be found on the Skylines Australia QLD Car Club forum - http://www.sauqld.com/ipb/index.php?showtopic=1896

Finally got it off at last. I got someone to pull on the tyre while I wound it and it moved just enough to get the tyre off. Unbolted the winch from underneath and by the look of the winch its stuffed. Dunno if the guy I bought the car off broke it or what but here is a pic of it. Hoping to get one from a wreckers maybe. Also not sure about tyre sizes that are on it. The tyres on it at the moment are 245/40 R18 93W and the spare is a speed restricted (80km/h) 235/45 R17 93W. I'd say I can drive with it on it since its the factory spare and the wheels are the standard rims. Anyone know if its ok to drive with the spare on it? It wont stuff the alignment etc?

Lucky I wasn't on the side of the road with a flat. I would be pissed at ford. Hopefully if there isn't another way of getting it down I can book it in for ford to fix it. Would it be covered under warranty if I have done engine mods etc? Or does doing mods void warranty on the whole car

Just went to change a tyre so I can get the other repaired and have discovered the winch is stuffed. It is an 06 model ute and I have never used the winch before so maybe it's siezed. When u wind it just makes a clunking noise and doesn't move. It has come down about 5cm but now won't move. Does anyone know how to fix this problem?

How much have people paid to have the pump installed? And where did you get it done?

You may notice that its a bit louder but not much

Has anyone tried having the exhaust come out the sides where the xr6 logo is? This would only be legal for the utes I believe

I replaced the cat and the centre mufflers with two hotdogs and was thinking of buying the straight through pipes off ebay to replace the rear muffler. Anyone done this?

[quote name='RAP1D' post='755693' date='Oct 26 2008, 03:09 PM']These are the 1% Flow Tolerance mate[/quote] no worries. count me in then for a set. Send me your account details and i will transfer the money

sorry thought they were the + / - 1% Flow Tolerance (2% Flow Window). But these are the + / - 5% (10% Flow Window) arnt they?

I bought some siemans deka injectors with a flow tolerance of + / - 5% (10% Flow Window) the other week. I had another look this week on the net and they are selling siemans deka premium injectors that are “FLOW MATCHED” to + / - 1% Flow Tolerance (2% Flow Window). Does the flow tolerance really make much difference? And is it worth an extra $200 for the difference it makes?

Yeah you just seem to hear a few bad reports about the walbro pump. I'm goin to get my mechanic to do it when he does the service. Is the bosch in tank pump really much more difficult to install?

I'm getting a new fuel pump for my ute but dont want to go with the surge tank. What's the best bosch pump that will fit in where the factory intank pump is? Car will prob have 330rwkw once tuned

Just wondering if xr6 turbo developments are still in business? Have sent them two emails about a fuel pump and have had no reply. Anyone know if they still sell the xr6t parts anymore?

Is half an inch really goin to make much difference though?

Prob used as a getaway car or to transport drugs through the ghetto haha